Slab Leak Detection & Repair in Kilgore, TX

What's Included in Our Slab Leak Detection & Repair Service

• Acoustic leak detection to hear escaping water through the slab
• Pressure testing to confirm the system is losing water and isolate supply vs. drain
• Electronic pipe and leak locating to fix the exact position before any concrete is cut
• A meter test to verify the leak and estimate how much water is being lost
• Targeted slab access opened only over the confirmed failure
• Spot repair, above-slab reroute, or repipe recommendation matched to the pipe’s condition
• Concrete cut and patch coordination where slab access is used
• Written documentation of the leak location and the repair for your records and insurance

Detect first, dig last

We use acoustic detection, pressure testing, and a pipe locator to fix the leak’s position before touching the slab. That is the difference between opening one square of concrete and jackhammering a room. Once located, we recommend the least-invasive option that actually fits the pipe — sometimes a reroute above the slab is smarter than digging.

• Acoustic and pressure detection to pinpoint the leak
• Targeted slab access over the confirmed failure
• Above-slab reroute when it avoids major concrete work
• Full re-pipe when the under-slab system is failing broadly

Why East Texas clay drives slab leaks

Kilgore’s red-clay and sandy-loam soils are expansive: they swell when our 47-plus inches of annual rain soak in and shrink hard in dry spells. That movement flexes the slab and the pipes cast into it, wearing through copper at friction points and pulling joints apart. It is a leading local cause — and why detection, not demolition, has to come first.

Repair, reroute, or repipe — how we choose

The right fix depends on the pipe’s condition and how the leak sits under the slab. A single failure in sound copper may only need a spot repair once we have opened the concrete directly over it. But copper that is leaking from clay movement has usually been rubbing and flexing across its whole run, so a second and third leak often follow the first. In those cases an above-slab reroute — running a new line up the wall, through the attic, and back down, abandoning the bad segment — avoids repeated slab work and frequently costs less over time. When the under-slab system is failing broadly, a repipe ends the cycle for good. A Kilgore planning range for pipe rerouting runs $577–$1,236 and main-water-line repair $379–$3,035 — planning ranges, not quotes; access, depth, pipe involved, and surface restoration all move the real number, which we put in writing after we see the leak.

What a slab leak does if you wait

A slab leak does not stay a plumbing problem for long. A hot-water leak can warm floors and drive humidity that damages flooring and baseboards; either kind saturates the soil under the foundation, which feeds the very clay movement that caused the leak and can worsen foundation cracking and heaving. Water finds its way up through the slab into carpet and wood, and standing moisture invites mold. That is why we treat detection as urgent even though a slab leak is not a burst-pipe emergency — the sooner it is located and fixed, the smaller the repair and the collateral damage.

Our Slab Leak Detection & Repair Process

1. 1

   Confirm there really is a slab leak

   Before anything invasive, we verify the symptom. A meter test with every fixture off tells us water is escaping; a pressure test tells us whether it is the pressurized supply side. Warm floor spots point toward a hot-water line. We rule out surface sources — a fixture, a water heater, an irrigation line — so we are not chasing the wrong problem.

2. 2

   Pinpoint the leak location

   We use acoustic detection and an electronic pipe locator to fix the leak’s position within the slab as closely as the equipment allows. This is the step that decides everything downstream — the difference between opening one square of concrete and jackhammering a whole room hoping to get lucky.

3. 3

   Weigh spot repair against reroute

   With the leak located and the pipe’s age and condition understood, we lay out the options. A single failure in otherwise sound pipe often justifies a targeted spot repair. If the line has already leaked before or the copper is failing at multiple friction points, an above-slab reroute that abandons the bad segment is frequently smarter and less destructive than repeated digs.

4. 4

   Make the least-invasive fix that lasts

   We open only what the evidence justifies, replace or reroute the failed line, and pressure-test the repair before closing anything. Where the whole under-slab system is failing, we discuss a repipe so you are not paying to chase leaks one at a time for years.

5. 5

   Patch, test, and document

   We restore the slab access, verify the system holds pressure, and document the leak location and the work performed. Slab-leak damage is often an insurance matter, so clear photos and a written scope give you what a claim requires.

Slab Leak Detection & Repair Near You

We provide slab leak detection & repair across Kilgore and East Texas, including Longview, White Oak, Gladewater, Overton, and Liberty City. Not sure if we reach you? See all service areas or call (831) 290-4327.

Slab Leak Detection & Repair FAQs