Leak Detection & Repair in Kilgore, TX

What's Included in Our Leak Detection & Repair Service

• Acoustic leak detection on pressurized supply lines to hear escaping water
• A pressure test to confirm the system is losing water and isolate which side
• Pipe locating and water-meter observation to narrow the leak to a point
• A clear read of what each test confirms — and what is still being verified
• Targeted access over the confirmed leak, opening only what the evidence justifies
• The repair itself — spot repair, reroute, or replacement — based on the pipe’s condition
• A written price before any wall or slab is opened
• Documentation of the leak location and repair for your records and insurance

How we pinpoint a leak

Acoustic leak detection listens for escaping water through specialized equipment. Pressure testing checks whether a closed system holds — telling us there is a leak before we know exactly where. A pipe locator and meter observation narrow it down. The method depends on the symptom, the pipe access, and the system’s condition, and we explain what each result actually confirms.

The sequence is deliberate. We prove a leak exists and isolate the side before we spend time hunting a spot, because chasing a sound on a system that turns out to hold pressure wastes your money. Once the pressure test says the supply side is losing water, the acoustic gear and locator earn their keep by turning a whole-house mystery into a point on the floor or in a wall.

It is not magic, and we do not pretend otherwise. Concrete, background noise, and pipe depth all affect how clean the read is. Where a single method is inconclusive, we cross-check with a second before we recommend opening anything — because the cost of being wrong is a hole in the wrong place.

• Acoustic detection for pressurized supply lines
• Pressure testing to confirm and isolate loss
• Pipe locating and meter checks to narrow the area
• Targeted access — the repair opens only what the evidence justifies

Slab leaks and East Texas clay

The red clay and sandy-loam soils around Kilgore swell and shrink with our wet-and-dry cycles, stressing the copper and older lines run under slab foundations. That movement is a leading cause of slab leaks here. When we suspect one, we detect first, then discuss whether a spot repair, a reroute above the slab, or replacement fits the pipe’s condition.

The mechanism is simple once you see it. When the clay soaks up our 47-plus inches of annual rain it expands and lifts; when it dries hard in a Texas summer it shrinks and drops. The slab and every pipe cast into it ride that movement, and copper wears through where it rubs a burr or a joint gets pulled apart. It is not bad plumbing — it is the ground doing what East Texas clay does.

That is exactly why detection has to come before demolition on a slab. Opening concrete is expensive and disruptive, and guessing wrong means doing it twice. Sometimes the smartest fix is not to chase the pipe under the slab at all but to reroute that line overhead — we lay out that trade-off honestly based on how much of the under-slab system is failing.

What a high water bill is telling you

A water bill that jumps with no change in your habits is one of the most reliable hidden-leak signs there is. Water that is escaping still registers on the meter, so a running toilet flapper, a slab leak, or a cracked supply line all show up as dollars before they ever show up as a stain. The meter is the honest witness — if the low-flow dial creeps with every fixture off, something is leaking.

We start there because it is cheap and decisive. A quick meter test tells us whether to keep looking, and roughly how big the leak is. From there, detection localizes it. Catching a slab or supply leak early, from the bill rather than from a flooded floor, is the difference between a targeted repair and a repair plus water-damage restoration.

• Check the meter with every fixture off — a creeping dial means a leak
• A running toilet is the most common invisible water-waster
• Warm floor spots point to a hot-side slab leak
• Musty smells and returning stains mean water is already in the structure

Repair, reroute, or replace

Once the leak is located, the right fix depends on the pipe’s overall condition, not just the one failure. A single break in otherwise sound pipe is a spot repair. When a line under the slab has failed once, and the pipe is old enough that more failures are likely, rerouting that run above the slab is often smarter than opening concrete now and again next year.

When the failures are widespread — pinholes showing up across an aging copper or galvanized system — repeated spot repairs stop making sense and a repipe becomes the economical answer. We show you the trade-offs with the actual condition of your pipe in front of you, so you are choosing with information rather than reacting to whichever leak sprang first.

Our Leak Detection & Repair Process

1. 1

   Call and describe the signs

   A jumped bill, a spinning meter, warm floor spots, or a running-water sound behind a wall each steer the search. Tell us what you have noticed and when it started.

2. 2

   Confirm there is a leak

   We start with a meter check and a pressure test to prove the system is actually losing water and to isolate whether it is on the supply side, before we spend your money hunting a location.

3. 3

   Pinpoint the location

   Acoustic detection, pipe locating, and meter observation narrow the leak to a specific point. We keep going until the evidence agrees on one spot — not a rough area.

4. 4

   Written options

   You get the confirmed location and the repair options in writing — spot repair, reroute, or replacement — with the price and the reasoning, before anything is opened.

5. 5

   Targeted repair

   We open only over the confirmed failure, make the repair, and — where a reroute avoids tearing up concrete — take that path instead. The goal is the smallest sound fix.

6. 6

   Test and document

   We pressure-test again to confirm the leak is gone, then document the location and the work so you have a clean record for insurance or your own files.

Leak Detection & Repair Near You

We provide leak detection & repair across Kilgore and East Texas, including Longview, White Oak, Gladewater, Overton, and Liberty City. Not sure if we reach you? See all service areas or call (831) 290-4327.

Leak Detection & Repair FAQs